This paper proposes a procedure for avoiding delay faults in field with slack assessment during standby time. The proposed procedure performs path delay testing and checks if the slack is larger than a threshold value using selectable delay embedded in basic elements (BE). If the slack is smaller than the threshold, a pair of BEs to be replaced, which maximizes the path slack, is identified. Experimental results with two application circuits mapped on a coarse-grained architecture show that for aging-induced delay degradation a small threshold slack, which is less than 1 ps in a test case, is enough to ensure the delay fault prediction.

A wavelet based algorithm for scalable video compression is described, with the main focus put on memory bandwidth reduction and efficient VLSI implementation. The proposed algorithm adopts a modified 2-D subband decomposition scheme in conjunction with a partial zerotree search for efficient Embedded Zerotree Wavelet coding. The experiment with the performance of the proposed algorithm in comparison with that of conventional DWT, MPEG-2, and JPEG demonstrates that the image quality of the proposed algorithm is consistently superior to that of JPEG, and our scheme can even outperform MPEG-2 in some cases, although it does not exploit the inter-frame redundancy. In spite of the performance inferiority to the conventional DWT, the proposed algorithm attains significant reduction of DWT memory requirements, enhancing a reasonable balance between implementation cost and image quality.

This paper presents a multi-channel biomedical sensor system with system-level chopping and stochastic analog-to-digital (A/D) conversion techniques. The system-level chopping technique extends the input-signal bandwidth and reduces the interchannel crosstalk caused by multiplexing. The system-level chopping can replace an analog low-pass filter (LPF) with a digital filter and can reduce its area occupation. The stochastic A/D conversion technique realizes power-efficient resolution enhancement. A novel auto-calibration technique is also proposed for the stochastic A/D conversion technique. The proposed system includes a prototype analog front-end (AFE) IC fabricated using a 130 nm CMOS process. The fabricated AFE IC improved its interchannel crosstalk by 40 dB compared with the conventional analog chopping architecture. The AFE IC achieved SNDR of 62.9 dB at a sampling rate of 31.25 kSps while consuming 9.6 μW from a 1.2 V power supply. The proposed resolution enhancement technique improved the measured SNDR by 4.5 dB.

3-D sound using head-related transfer functions (HRTFs) is applicable to embedded systems such as portable devices, since it can create spatial sound effect without multichannel transducers. Low-order modeling of HRTF with an IIR filter is effective for the reduction of the computational load required in embedded applications. Although modeling of HRTFs with IIR filters has been studied earnestly, little attention has been paid to sound movement with IIR filters, which is important for practical applications of 3-D sound. In this paper, a practical method for sound movement is proposed, which utilizes time-varying IIR filters and variable delay filters. The computational cost for sound movement is reduced by about 50% with the proposed method, compared to conventional low-order FIR implementation. In order to facilitate efficient implementation of 3-D sound movement, tradeoffs between the subjective quality of the output sound and implementation parameters such as the size of filter coefficient database and the update period of filter coefficients are also discussed.

In this paper, a specified hardware architecture of the Fast Mode Decision (FMD) algorithms presented by our previous work is proposed. This architecture is designed as an embedded mode dispatch module. On the basis of this module, some unnecessary modes can be skipped or the mode decision process can be terminated in advanced. In order to maintain a higher compatibility, the FMD algorithms are unitedly designed as an unique module that can be easily embedded into a common video codec for H.265/HEVC. The input and output interfaces between the proposed module and other parts of the codec are designed based on simple but effective protocol. Hardware synthesis results on FPGA demonstrate that the proposed architecture achieves a maximum frequency of about 193 MHz with less than 1% of the total resources consumed. Moreover, the proposed module can improve the overall throughput.

We propose a jitter amplifier architecture for an oscillator-based true random number generator (TRNG). Two types of latency-controllable (LC) buffer, which are the key components of the proposed jitter amplifier, are presented. We derive an equation to estimate the gain of the jitter amplifier, and analyze sufficient conditions for the proposed circuit to work properly. The proposed jitter amplifier was fabricated with a 65 nm CMOS process. The jitter amplifier with the two-voltage LC buffer occupied 3,300 µm2 and attained 8.4x gain, and that with the single-voltage LC buffer achieved 2.2x gain with an 1,700 µm2 area. The jitter amplification of the sampling clock increased the entropy of a bit stream and improved the results of the NIST test suite so that all the tests passed whereas TRNGs with simple correctors failed. The jitter amplifier attained higher throughput per area than a frequency divider when the required amount of jitter was more than two times larger than the inherent jitter in our test-chip implementations.

This paper proposes a mixed-grained reconfigurable architecture consisting of fine-grained and coarse-grained fabrics, each of which can be configured for different levels of reliability depending on the reliability requirement of target applications, e.g. mission-critical applications to consumer products. Thanks to the fine-grained fabrics, the architecture can accommodate a state machine, which is indispensable for exploiting C-based behavioral synthesis to trade latency with resource usage through multi-step processing using dynamic reconfiguration. In implementing the architecture, the strategy of dynamic reconfiguration, the assignment of configuration storage and the number of implementable states are key factors that determine the achievable trade-off between used silicon area and latency. We thus split the configuration bits into two classes; state-wise configuration bits and state-invariant configuration bits for minimizing area overhead of configuration bit storage. Through a case study, we experimentally explore the appropriate number of implementable states. A proof-of-concept VLSI chip was fabricated in 65nm process. Measurement results show that applications on the chip can be working in a harsh radiation environment. Irradiation tests also show the correlation between the number of sensitive bits and the mean time to failure. Furthermore, the temporal error rate of an example application due to soft errors in the datapath was measured and demonstrated for reliability-aware mapping.

An NMOS 4-phase dynamic logic scheme is described, which is intended to achieve low-power consumption in the deep submicron design. In this scheme, the short-circuit current is eliminated, and moreover, the voltage swing of transition signals is reduced, resulting in enhancing power reduction effectively. First, distinctive features of this 4-phase dynamic logic are specified, as compared with the static CMOS logic and dynamic domino CMOS logic. Then, power simulations are attempted for the 4-phase dynamic logic, static CMOS logic, dynamic CMOS logic, and pass-transistor logic, by using a number of logic modules, which demonstrate that the NMOS 4-phase dynamic logic is the most power-efficient. Moreover, through the gate delay simulation, the capability of how many transistors can be packed in a logic block is also discussed.

This paper presents an architecture of signal-dependent analog-to-digital converter (ADC) based on MINIMAX sampling scheme that allows achieving high data compression rate and power reduction. The proposed architecture consists of a conventional synchronous ADC, a timer and a peak detector. AD conversion is carried out only when input signal peaks are detected. To improve the accuracy of signal reconstruction, MINIMAX sampling is improved so that multiple points are captured for each peak, and its effectiveness is experimentally confirmed. In addition, power reduction, which is the primary advantage of the proposed signal-dependent ADC, is analytically discussed and then validated with circuit simulations.

In tooth contour extraction there is insufficient intensity difference in x-ray images between the tooth and dental bone. This difference must be enhanced in order to improve the accuracy of tooth segmentation. This paper proposes a method to improve the intensity between the tooth and dental bone. This method consists of an estimation of tooth orientation (intensity projection, smoothing filter, and peak detection) and PCA-Stacked Gabor with ellipse Gabor banks. Tooth orientation estimation is performed to determine the angle of a single oriented tooth. PCA-Stacked Gabor with ellipse Gabor banks is then used, in particular to enhance the border between the tooth and dental bone. Finally, active contour extraction is performed in order to determine tooth contour. In the experiment, in comparison with the conventional active contour without edge (ACWE) method, the average mean square error (MSE) values of extracted tooth contour points are reduced from 26.93% and 16.02% to 19.07% and 13.42% for tooth x-ray type I and type H images, respectively.

The decentralized energy network is one of the promising solutions as a next-generation power grid. In this system, each house has a photovoltaic (PV) panel as a renewable energy source and a battery which is an essential component to balance between generation and demand. The common objective of the battery management on such systems is to minimize only the purchased energy from a power company, but battery degradation caused by charge/discharge cycles is also a serious problem. This paper proposes a State-of-Health (SOH) aware system-level battery management methodology for the decentralized energy network. The power distribution problem is often solved with mixed integer programming (MIP), and the proposed MIP formulation takes into account the SOH model. In order to minimize the purchased energy and reduce the battery degradation simultaneously, the optimization problem is divided into two stages: 1) the purchased energy minimization, and 2) the battery aging factor reducing, and the trade-off exploration between the purchased energy and the battery degradation is available. Experimental results show that the proposed method achieves the better trade-off and reduces the battery aging cost by 14% over the baseline method while keeping the purchased energy minimum.